Concrete Floor Acid Stain Application
A. Preparation of Existing Concrete Surface
Curing agents, sealers, paints, coatings, waxes or water repellants must be removed prior to the concrete acid stain application. Mechanical methods of removal are not advised as they may scratch the surface leaving unsightly patterns of scratches in the surface.
Older concrete surfaces need to be tested for acceptance of the acid stain. The cleaned surface must be penetrable by water. If water beads on the surface and is not readily absorbed into the concrete, mild acidic detergents such as a concrete renovator may be of assistance in your concrete acid stain application. Never acid etch concrete to be acid stained. This will use up the free lime in the concrete and leave you with a surface that is not stainable for concrete floor acid stain application.
B. New Concrete:
Freshly poured concrete should be sufficiently cured, a minimum of thirty days before the concrete floor acid stain application. If score patterns are desired, a diamond blade grinder may be used to score various patterns, borders or designs onto the surface prior to, or after concrete acid stain application. If light colored grout lines are desired score after staining process is complete.
Freshly poured or recently poured concrete needs to be scrubbed thoroughly, sometimes more thoroughly than old concrete due to what is known as latency, this is the "dust", if you will that remains on top of the concrete after it is poured and cured.
This latency will not allow the concrete floor acid stain to penetrate as is needed to provide a beautiful concrete acid stain application so we need to use a floor maintainer (buffer) with a black or green scrub pad and TSP (trisodium phosphate) or our favorite, Dyna Blue, to scrub and shop vac the floor clean.

C. Cleaning of Concrete:
These next two steps will take you from having a good concrete stained floor to a Fantastic concrete acid stain application. As we say in the Decorative Concrete industry, application of the pretty stuff is easy but the preparation of the concrete is what makes the difference and boy will this make a difference as you'll see and be very happy you took the time and effort to do it.
First we need to scrape the paint and other things off the concrete before the concrete floor acid stain process, you will not find them all but when you wet the concrete you will see everything as we see here, we have scrubbed the concrete and are now vacuuming.
D. Citrus-Degreaser
This is a very important step and most manufacturers and even many "acid stain professionals" don't take this next step in the concrete floor acid stain process, which is critical to a beautiful concrete floor acid stain application for your floor. If the floor has some oil or grease or really anything questionable on it we recommend that you clean the floor with Citrus Degreaser. Dilute with 8 parts water and scrub the floor with a black pad and a buffer. Rinse and use a shop-vac to remove residue, if possible always use a shop vac as this will pull the residue and dirt out of the pores of the concrete.
This step is only necessary if your concrete is extremely dirty. If your concrete is normal or just slightly dirty the following process is all that is normally needed.
E. Concrete Renovator
Next dilute Dyna-Blue, 2 parts water to 1 part Dyna Blue. Moisten the concrete and use a garden sprayer with all plastic inserts to spray the dilution over the entire floor and scrub lightly. Make sure to have proper ventilation. Let the mixture stand for approximately 5 minutes or until all fizzing and bubbles have ceased.
Use a buffer with a black pad and scrub the floor thoroughly. Flood the floor with water and shop vac the floor to achieve the cleanest floor possible for concrete floor acid stain application.
F. Coverage
Make sure that your concrete is completely dry. This sounds like an obvious statement but you would be very surprised to know how many folks take this for granted. When we say dry we mean that it is better to leave the floor overnight to dry unless it is summer and the AC is on and a few fans are turned on. The reason for this precaution is that is if the concrete is wet or even slightly damp this will dilute the concrete floor acid stain and probably require you to spray again, therefore this is essential in the concrete acid stain application process.
One coat of Acid Stain is all that is usually needed. You may feel that you want to go back over the area and spray a little more in some areas. Acid Stain can be applied at a rate of 1 part water to 1 part stain. The coverage rate will be 135-200 square feet per gallon. When applicable after you have tested the stains in an inconspicuous area, you may choose to dilute the stains more to achieve a slightly lighter color. .
G. Concrete Stain Application
For an excellent concrete floor acid stain application all surfaces must be completely dry, prepared and tested as described above. Acid Stain should be shaken well and poured directly into a plastic sprayer with a plastic filter and internal acid resistant plastic parts. The sprayer should be continuously pumped to keep a constant pressure while applying concrete floor acid stain. We are very partial to a battery operated backback sprayer sold by Crusader Manufacturing, which will spray 120 gallons on a single charge. It sells for around $200.00 and if you are going to be doing a lot of staining it is well worth the cost.
Hold the tip of the sprayer approximately eighteen to twenty-four inches from the concrete surface and spray onto the slab, being careful not to let the liquid drip out of the spray tip as this may leave visible drip marks on the concrete. There is no need to hold the sprayer closer to the ground unless you might be "working" an edge.
We recommend that you use a car wash brush with nylon bristles to gently scrub the concrete stain into the concrete but it is not necessary if you are applying the concrete floor acid stain yourself, just wet the concrete thoroughly with the stain. After the first coat is applied and has completely dried, a second coat can be applied if a darker color is desired. We recommend that you walk on the surface in clean socks or surgical booties so as not to leave “shoe prints” on the surface. The second coat of concrete stain should be allowed to work into the concrete for 1-2 hours.

Did you find this article useful? For more useful tips and hints, points to ponder and keep in mind, techniques, and insights pertaining to Internet Business, do please browse for more information at our websites.
http://www.adsence-dollar-factory.com
http://www.100earningtips.com

This entry was posted on Tuesday, October 13th, 2009 at 4:11 pm and is filed under Business. You can follow any responses to this entry through the RSS 2.0 feed. You can leave a response, or trackback from your own site.